Bare Knuckle 280K Stand. Shaft Split Pot

7

Potentiometer for Guitar & Bass

  • Resistance curve: logarithmic (Custom Audio Taper)
  • Specially made for Bare Knuckle by CTS
  • Smooth torque and +/- 10% tolerance
  • Resistance: 280 kOhm
  • Standard axis: Corrugated
  • Shaft diameter: 6 mm
  • Total shaft length: 19 mm
  • Thread length: 10 mm
  • Thread diameter: 10 mm
  • Hosuing diameter: 24 mm
  • Includes washer, tooth lock washer and nut
  • Made in USA
Available since December 2020
Item number 507613
Sales Unit 1 piece(s)
Design Split Shaft
Resistance Value 280 kOhm
Characteristic Curve Logarithmic
Thread Length 9,0 mm
Tandem Poti No
Push/Push No
Solderless No
shaft type grooved
$13.30
The shipping costs are calculated on the checkout page.
In stock within 1-2 weeks
In stock within 1-2 weeks

This product is expected back in stock soon and can then be shipped immediately.

Standard Delivery Times
1

7 Customer ratings

4.6 / 5

You have to be logged in to rate products.

Note: To prevent ratings from being based on hearsay, smattering or surreptitious advertising we only allow ratings from real users on our website, who have bought the equipment from us.

After logging in you will also find all items you can rate under rate products in the customer centre.

quality

7 Reviews

T
Good quality CTS pots that measured SPOT ON 280k.
TCSMD 10.10.2021
I got these for a P90 equipped guitar. I find 250k a bit low for P90s and 500k is way too high for my taste. I prefer audio taper so the linear 300k Gibson pots wasn't an option for me and I can't seem to find audio taper 300k pots anywhere.

These 280k pots seemed interesting. I ordered two and I hoped that with a bit of luck they would be slightly higher than 280k or at least not lower.

As it turned out one measured exactly 280k and the other one measured 281k. I had hoped they would be slightly higher but I can't really complain when they were EXACTLY as specified.

Of course I can't really say much about tolerance from such a small number of specimens but it looks pretty tight.

The quality of the pots is just like standard CTS pots (which means they're very good!).

Highly recommended if you want audio taper with slightly higher resistance than standard 250k pots.
quality
1
1
Report

Report

google translate de
Unfortunately there was an error. Please try again later.
P
Für ein wenig mehr Höhen....
Patrick396 26.07.2021
Ich habe dieses Poti eingebaut um ein etwas älteres kratzendes zu ersetzten und wegen dem etwas höheren 280-ohm Wert ein wenig mehr "frische" in meine Strat zu bekommen. Leichtgängig ist es...aber leider hielt es nicht so lange und fing auch nach ein paar Wochen an zu "kunspern". Da ich nichts von "kontaktspray Reparaturen" halte (in der Regel hält das auch nicht lange und wird nur schlimmer..) musste ich es wieder ausbauen und habe jetzt teure Dunlop 250 Pots drinnen, die ewig halten sollen....das tun sie auch. Leider für Thomann diese Poti nicht....
quality
0
0
Report

Report

google translate de
Unfortunately there was an error. Please try again later.
A
Das Quäntchen mehr...
Axilla 17.08.2021
...an Offenheit / Höhen und Output bei Singlecoils / Goldfoil Pickups.
Sehr gute Regelkurve und ich werde da wieder zugreifen.
quality
0
0
Report

Report