A
Avoids marking your rack gear
These washers are for M6 rack screws that are pretty standard. They are quite a big diameter and spread the load well. The screws locate tight in the centre and don't move about so they are concentric when you tighten them up. Most importantly they won't mark your gear.
As they are quite a big diameter and slightly more so than the cheaper softer ones so you need to be careful when using on the very top or bottom of racks as it can catch on the racking. It could also overlap units when using 1U or other rack units where the holes are at the very top or bottom. There's a way around this should you come across these problems and that's by shaving a slice off. It worked for me and they still perform the job well.
As they are quite a big diameter and slightly more so than the cheaper softer ones so you need to be careful when using on the very top or bottom of racks as it can catch on the racking. It could also overlap units when using 1U or other rack units where the holes are at the very top or bottom. There's a way around this should you come across these problems and that's by shaving a slice off. It worked for me and they still perform the job well.
1
0
Report
RS
Good quality Washers!!
We needed to purchase a good amount of washers for a new studio install and we wanted something a little more sturdy than the usual soft flexible ones. They are sturdy and of good quality. No complains at all!
0
0
Report
R
Perfect again by Adam Hall
Really nice Plastic Washer. They are great in combination of ADAM HALL 5410BLK RACK SCREW.
We bought a pair of packs, and they are really nice , lucid black.
Everything as described. We tried to other Screws too, and they were perfect too.
We bought a pair of packs, and they are really nice , lucid black.
Everything as described. We tried to other Screws too, and they were perfect too.
0
0
Report
D
Simple product does the job
Not much to say really, they are great for the job.
0
0
Report
B
Scratch-free Rack Units
These plastic washers are good for keeping you rack units free of scratches. They are good quality and do not break easily. Unfortunately, they are a little too big and may stick out over the edge of the rack unit, if placed too close to it. But this is only a problem when placing 1U units next to each other, and it is not too difficult to plan around it.
0
0
Report
V
Not recommended for 1U use
When used on 1u modules or faceplates the washers will actually overlap others modules or faceplates. In other words, for 2U and 3U etc. it won't be a problem, but they're too large for 1U, in my case rendering them useless.
0
0
Report
D
Sturdy
This are way sturdier than previous ones I've had, although the only con is that they are so big it makes kind of difficult to make them work when screwing units together.
0
0
Report
B
Obvious
What can one say about plastic washers? They protect your rack gear and they are what they are.
0
0
Report
C
Perform their function nicely
It's pretty hard to rate something as simple as a plastic washer. They do their job nicely it must be said and there were no bogus examples in any of the packets that I bought.
My only word of warning for those considering these washers: these washers are best utilised when you have large rack gear (3RU or higher) where the mounting holes are centred. If you have a lot of narrow rack gear (1RU or 2RU) where the mounting holes are typically on the top and bottom edges, go for the Adam Hall 5621 Nylon Washers instead. This way your rack gear will stack properly within its designated space!
My only word of warning for those considering these washers: these washers are best utilised when you have large rack gear (3RU or higher) where the mounting holes are centred. If you have a lot of narrow rack gear (1RU or 2RU) where the mounting holes are typically on the top and bottom edges, go for the Adam Hall 5621 Nylon Washers instead. This way your rack gear will stack properly within its designated space!
0
1
Report
A
Impressive!
I receive order for 10 days in Macedonia.
3 days the goods stay in warehouse for custom control.
So the Thomann fast preparing goods only for one working day.
The quality of products is very well, I m still in test mode, some of the stuff but from the first view is Very good.
The box is too big for my products but all the products was protected in the box.
Soon i will order again, thanks Thomann.
3 days the goods stay in warehouse for custom control.
So the Thomann fast preparing goods only for one working day.
The quality of products is very well, I m still in test mode, some of the stuff but from the first view is Very good.
The box is too big for my products but all the products was protected in the box.
Soon i will order again, thanks Thomann.
0
0
Report
