G
6U Rack stand that is really only a 4U
This stand is a decent stand. It is tough and seems to be built well. The metal seems of good quality for sure. However, the stand has a big down side in regards to its function. There is a support strut that goes across the top of the stand. Well this pretty much rules out the chance of installing any 1u rack device. You just cannot avoid this strut. So your robbed of basically the top 1u slot. The next thing that robs you of another 1u is the fact that the stand is too low to allow the bottom 1U space to be filled. As others have said this stand is more like a 4U.
I guess it's down to poor design that two 1U slots are made redundant. So be careful in your choice of stand. Luckily there was no great urgency for me to have 6U, I just chose this stand for the extra space available if I need it perhaps in the future.
One other thing, which is not a big deal, but it would have saved some time. There is no guide on how to setup the stand. It is straight forward but a simple diagram would have helped. Must things come with set up diagrams, it's not a big ask to have had one supplied. I had to go onto the website again to see what the stand looked like so I didn't install the strut and the rear bar in opposite positions.
Performance wise the stand holds up well. It seems quite sturdy and so long as it's not abused it will hold your rack gear no problem. Obviously it will not take a huge 4U rack PA as this would just be too heavy. But it will hold your 1 U preamps and EQs and noise gates with no issues and it sits very stable on a flat surface such as a desk or cabinet.
I guess it's down to poor design that two 1U slots are made redundant. So be careful in your choice of stand. Luckily there was no great urgency for me to have 6U, I just chose this stand for the extra space available if I need it perhaps in the future.
One other thing, which is not a big deal, but it would have saved some time. There is no guide on how to setup the stand. It is straight forward but a simple diagram would have helped. Must things come with set up diagrams, it's not a big ask to have had one supplied. I had to go onto the website again to see what the stand looked like so I didn't install the strut and the rear bar in opposite positions.
Performance wise the stand holds up well. It seems quite sturdy and so long as it's not abused it will hold your rack gear no problem. Obviously it will not take a huge 4U rack PA as this would just be too heavy. But it will hold your 1 U preamps and EQs and noise gates with no issues and it sits very stable on a flat surface such as a desk or cabinet.
6
0
Report
I
Well Made Rack
Hey, babe. Nice rack!
Thanks, it's the Adam Hall STRS6U and boy is it sturdy! Fill it up and it's even sturdy enough to use the top horizontal bar as a handle, depending on the weight of course.
Thanks, it's the Adam Hall STRS6U and boy is it sturdy! Fill it up and it's even sturdy enough to use the top horizontal bar as a handle, depending on the weight of course.
3
0
Report
B
I confirm the other reviews
Screw holes are badly made. I had 2 screw holes totally unusable. I would need to drill and remove metal elements that are blocking screws from a normal screwing. So immediately, 1U is totally unusable.
If not that, then top 1U would be actually totally usable on the contrary to other comments. This top bar/rod doesn't need to be mounted.
The stability is excellent. After mounting just 1U unit, it has become stable already. Now when I have 3U filled, there's nothing to complain. It sits on my desk, and even that small part of it is beyond the desk, it's super stable.
I bought this rack for two devices: Focusrite Scarlett 18i20 (second from the top) and Behringer Model D on the bottom (but not at the very bottom because holes in the rack ears didn't let me put it lower.
If not that, then top 1U would be actually totally usable on the contrary to other comments. This top bar/rod doesn't need to be mounted.
The stability is excellent. After mounting just 1U unit, it has become stable already. Now when I have 3U filled, there's nothing to complain. It sits on my desk, and even that small part of it is beyond the desk, it's super stable.
I bought this rack for two devices: Focusrite Scarlett 18i20 (second from the top) and Behringer Model D on the bottom (but not at the very bottom because holes in the rack ears didn't let me put it lower.
0
0
Report
M
Solid
If you?re looking for a rack that is solid, cheap and durable look no further. This rack will be in perfect shape in years to come as it?s built very solid and robust. At the same time lightweight. Great purchase!
0
0
Report
JQ
Good for lighter shallow units
This is a good desktop stand but I wouldn't want to fill it with heavy units - it's ideal for lighter, shallow depth rack gear. Probably not one to fill with full depth retro units. Due to the angle you'd be limited in what would fit the lower positions anyway. Overall very good as long as you don't expect the impossible.
0
0
Report
M
Aesthetic and Strong stuff
The Adam Hall Rack stand is very discrete and sturdy,sure it will not hold the wait of a Power Amplifier but for rack mount processors or audio interfaces the Adam Hall Rack is Great.For example an Eleven Rack + Roland studio capture fits well on it.
Easy to set up, no need of a manual or set up diagram.
Easy to set up, no need of a manual or set up diagram.
0
0
Report
A
Lowest spaces not usable for regular rack devices, didn't check this before buying. Check if the devices you want to mount aren't too deep.
0
0
Report
D
Ok!
A little bit hard in fitting when mount it together but stabile when filled with racks. Could be a little bit more precision but ok.
0
0
Report
Å
Works great for a cheap price
This rack works perfectly Ok. It is made to stand on a table. Become more steady when you were stuck some units.
0
0
Report
C
More like 4U in my opinion
The angle and construction make the two lowest Us practically unusable. The lowest U can’t even fit a patch bay
0
0
Report
