r
I didn't enjoy fitting them, but the results made it worthwhile
First, I bought these to fit on a PRS SE Tremonti Custom (2017). After reading many reports of people successfully fitting them, without issues. However, in my experience, it wasn't so straightforward. First, it required a lot of force to get the washer rings into place. And it took a lot of force to press the tuning machines in flush with the back of the headstock. In fact, I damaged the locking mechanism on one of the tuners from pushing too hard against it. Perhaps I should have removed the locking screws first. That one locking mechanism is a bit difficult to turn now, but it does work.
The new tuners weigh in at 42g heavier than the PRS SE stock tuners they replaced. And I don't notice any neck dive or any other issues.
What I do notice is that it is very easy to restring the guitar. And once the strings were stretched and tuned, the tuning is now very stable. I think the guitar was good before, but this is a nice upgrade. I don't regret getting them for this guitar, even though it was a harder job than expected.
The new tuners weigh in at 42g heavier than the PRS SE stock tuners they replaced. And I don't notice any neck dive or any other issues.
What I do notice is that it is very easy to restring the guitar. And once the strings were stretched and tuned, the tuning is now very stable. I think the guitar was good before, but this is a nice upgrade. I don't regret getting them for this guitar, even though it was a harder job than expected.
1
0
Report
SW
Great
I bought these for my PRS SE Holcomb sig. They are perfect drop in replacements. (They also fit all other SE's perfectly)
They are very easy to install, just a single screw and nut and that's it.
As you would expect with locking tuners, restringing is super quick. And the locks themselves are very secure and also don't seem to have any jagged edges that would damage or break your strings.
They are very stable when it comes to tuning. Just as good or better than Grovers. They easily beat out any stock tuner, especially with their higher gear ratio. It makes fine tuning way easier.
The posts are shorter, but more than long enough that they will still be long enough for 90% of headstocks. And they actually look really cool in my opinion being short. Has a classy look.
As for the colour, the chrome seems to be good. It doesn't blemish easily and doesn't "fade" the way some other chromes seem to, even with the most sweaty hands imaginable.
Overall they are very stable and secure, and the quality of life upgrade from restringing times being drastically shortened is great. I would and will be using Schaller locking tuners in all of my guitars in the future.
They are very easy to install, just a single screw and nut and that's it.
As you would expect with locking tuners, restringing is super quick. And the locks themselves are very secure and also don't seem to have any jagged edges that would damage or break your strings.
They are very stable when it comes to tuning. Just as good or better than Grovers. They easily beat out any stock tuner, especially with their higher gear ratio. It makes fine tuning way easier.
The posts are shorter, but more than long enough that they will still be long enough for 90% of headstocks. And they actually look really cool in my opinion being short. Has a classy look.
As for the colour, the chrome seems to be good. It doesn't blemish easily and doesn't "fade" the way some other chromes seem to, even with the most sweaty hands imaginable.
Overall they are very stable and secure, and the quality of life upgrade from restringing times being drastically shortened is great. I would and will be using Schaller locking tuners in all of my guitars in the future.
1
1
Report
t
First was was faulty, the second pack was just ok
The first pack of locking tuners was faulty.. I saw that only after changing the strings (and cutting them after locking!).. so I basically threw a pack of string out of the window.
The Thomann team saw through the video I sent the problem, and they sent me a new pack after I returned the original one through the Post office. The new pack was ok, but the mechanism is a little "unreliable".. sometimes it works smooth like butter, sometimes it works a little sluggish.
Note: This was fitted into a PRS SE Chris Robertson guitar.
The Thomann team saw through the video I sent the problem, and they sent me a new pack after I returned the original one through the Post office. The new pack was ok, but the mechanism is a little "unreliable".. sometimes it works smooth like butter, sometimes it works a little sluggish.
Note: This was fitted into a PRS SE Chris Robertson guitar.
2
0
Report
0
5 stars but...
I bought these, without doing my proper research. I bought them to replace the stock grover tuners on my Epiphone Les Paul, however to my dismay the shaft is not long enough for Les Paul's, (which should be 23mm instead of the 19mm).
Over all the packaging is really nice and simple, nothing wasted.
They appear to be really good quality, and just look so good. I can't wait to see if they will fit on some of my other guitars. In the meantime i've ordered the correct ones from Schaller directly (as thomann don't supply the ones i needed). Looking forward to trying them.
Over all the packaging is really nice and simple, nothing wasted.
They appear to be really good quality, and just look so good. I can't wait to see if they will fit on some of my other guitars. In the meantime i've ordered the correct ones from Schaller directly (as thomann don't supply the ones i needed). Looking forward to trying them.
0
0
Report
i
German made quality
They lock, they tune, they're well made.
Quite heavies, but, I guess it's a small price to pay for higher quality alloy used.
Be mindful of that if you have neck dive issues,
Quite heavies, but, I guess it's a small price to pay for higher quality alloy used.
Be mindful of that if you have neck dive issues,
0
0
Report
R
Replacement for PRS SE Custom 24
I used them to replace the stock tuners in my PRS SE Custom 24. They fit nicely but I had to add a tiny piece of toothpick in a few of the holes for the screws to set in place.
Schallers are a bit shorter than the stock ones being more flush with the headstock. Personally I think they look better that way.
Overall quality is great and the tuners work as expected by offering better tuning stability and ease of changing strings.
Schallers are a bit shorter than the stock ones being more flush with the headstock. Personally I think they look better that way.
Overall quality is great and the tuners work as expected by offering better tuning stability and ease of changing strings.
0
0
Report
EK
Does what it says on the tin
Ordered these for my PRS Tremonti SE 2017 and they fit right in place with no drilling needed.
Now I can use the whammy bar as intended without going out of tune! Awesome product as always from Schaller - can't go wrong.
Now I can use the whammy bar as intended without going out of tune! Awesome product as always from Schaller - can't go wrong.
2
0
Report
d
Excellent Quality - Fits PRS SE
Excellent German quality!
I've installed these on my PRS SE Tremonti 2017 and PRS SE Santana 2017 without the need of drilling or modifications.
Improved overall tuning stability.
I've installed these on my PRS SE Tremonti 2017 and PRS SE Santana 2017 without the need of drilling or modifications.
Improved overall tuning stability.
2
0
Report
JD
The best you can buy
Probably the best ones I ever tried for now, even better than the one that comes in my music man. Tuning is smooth, they keep the tuning.
They fit perfectly in the PRS holes with no issues, no additional hole is needed.
Probably too much for a PRS SE, but it worths it.
They fit perfectly in the PRS holes with no issues, no additional hole is needed.
Probably too much for a PRS SE, but it worths it.
0
0
Report
.
Schaller machine heads
The nut used to fix the machine heads is not proper for such a high quality product (the heads themselves are good btw): too thin and far too soft, even with my experience and quality tools the chrome got ripped of the nut and it looks like the metal was some sort of copper (which is absurd at this price), which led the nut itself to be destroied in no time, not worth the price for the nut alone.
0
0
Report
