s
Artec SE-2
Does what it says on the tin, used it to replace a faulty pre-amp on an old Vintage bass, worked as expected - quite easy to fit if you are handy with a soldering iron, all th eparst you need are here. Only small annoyance was the centre of the balance pot was not as easy to find, maybe could have been designed with a "click" when it is at dead centre. Output level is nice and strong and the frequencys of the one controls are well chosen, the treble adds a nice edge without dissolving into noise, bass pot too adds a nice boost to the bottom end. Suited my Vintage V1004 very well, but obviously could be too much for some guitars
1
0
Report
H
Does what it says on the tin
I bought this to replace a failed active circuit in a low cost bass. It is pre-wired, but you do need to solder the pickup, jack, and earth connections. So you need to be able to solder confidently to ensure a good installation.
The preamplifier and balance control circuit boards are quite deep, so would not suit a thin bass, indeed they only just fitted inside my HBZ-2500.
The sound is colourless and completely noise free, however the tonal range is not terribly wide, at least not with my pickups.
I am completely satisfied with this product at this price point. And I now have my bass working again. What's not to like?
The preamplifier and balance control circuit boards are quite deep, so would not suit a thin bass, indeed they only just fitted inside my HBZ-2500.
The sound is colourless and completely noise free, however the tonal range is not terribly wide, at least not with my pickups.
I am completely satisfied with this product at this price point. And I now have my bass working again. What's not to like?
1
0
Report
M
Perfectly Adequate
Like another buyer I've put mine in an old bass collection an SB 315
Instant improvement over old preamp.
I have better preamps in other more expensive basses and not a patch on some modern basses....but for the price it's great.
Much more depth and power on the lows, more depth to the tone.
Installation took 45 minutes could have been quicker if my 48 year old eyes were what they once were ....
Instant improvement over old preamp.
I have better preamps in other more expensive basses and not a patch on some modern basses....but for the price it's great.
Much more depth and power on the lows, more depth to the tone.
Installation took 45 minutes could have been quicker if my 48 year old eyes were what they once were ....
0
0
Report
n
A good upgrade for tight budget
I used my Artec SE-2 in a project bass I was putting together. Although the packaging was a little lacking, it did contain everything needed. For the most part it was relatively easy to install, but one concern I had was with the blend control. There are only three solder points for neck hot, bridge hot and ground - meaning you have to force two ground wires into one hole. I found this very difficult and in the end I had to come up with my own solution of making a "pin" by soldering a short length of solid core wire through the solder point, then soldering the two ground wires to the pin.
That aside, the rest of the install was easy with the snap on connectors. Soundwise, it has a decent range on the bass/treble controls and the blend worked smoothly.
I would recommend this to anyone who was thinking of upgrading an inexpensive bass, but I think there are better preamps/EQ out there if you want a little more quality.
That aside, the rest of the install was easy with the snap on connectors. Soundwise, it has a decent range on the bass/treble controls and the blend worked smoothly.
I would recommend this to anyone who was thinking of upgrading an inexpensive bass, but I think there are better preamps/EQ out there if you want a little more quality.
0
0
Report
C
Great for the price
I fitted this to a Bass Collection model. It's a vast improvement on the original. Wiring was straightforward following the diagram on their website. It's not too extreme in use and the treble boost is more hi mid than top, which is ideal for cutting through a band mix. Very satisfied especially for thje money.
0
0
Report
HL
It Is What It Is
Bought this as a backup for my S.U.B. - just in case . . .
0
1
Report
R
Artec SE-2
I installed it on a friends 6-string bass because the previous owner destroyed the pre-installed preamp, there where no instructions with the circuit that came, so I had to wing it.
The end result: a decent quality preamp, it does its job just fine and I haven't had any issues with it.
The end result: a decent quality preamp, it does its job just fine and I haven't had any issues with it.
0
0
Report
