K&M 24040 Microphone Holder Tuba

19

Microphone Holder for Tuba and Baritone

  • Black
  • For screwing to bell
  • Gooseneck approx. 20 cm
  • Max. load: 350 g
  • Microphone not included
Available since January 2001
Item number 146103
Sales Unit 1 piece(s)
Component type Special Mount
Length 200 mm
Mounting Thread
Show more
$38
The shipping costs are calculated on the checkout page.
In stock
In stock

This product is in stock and can be shipped immediately.

Standard Delivery Times
1

19 Customer ratings

4.1 / 5

You have to be logged in to rate products.

Note: To prevent ratings from being based on hearsay, smattering or surreptitious advertising we only allow ratings from real users on our website, who have bought the equipment from us.

After logging in you will also find all items you can rate under rate products in the customer centre.

quality

9 Reviews

C
Not used it for tuba but...
Chris606 07.10.2014
I use this gooseneck clamp stand for the kick drum mic.
The stage I usually work on is not very deep so any performers in front of the drummers quite often accidently knock the kick mic out of position, and most drummers seem to push the kick drum into the mic quite often too.
This clamps to the rim of the kick drum very solidly and the gooseneck is stiff enough to hold the mic in place.
I tend to position the clamp on the rim above the soundhole and 'dangle' the mic in to place. I currently use an Audix D6 kick drum mic, which is long enough to just poke through the kick drum soundhole, although I tend to position the kick mic about an inch from the skin of the drum, or just outside the hole.
I've only used it a few times and so far it does the job really well, and because there's no floor stand to get in the way the mic stays where I put it in the soundcheck.
On the down side, there is a lip on the 'foot' of the clamp which is a bit too long for drums with thin rims, but this is easily fixed by unscrewing the gooseneck from the clamp and re-attaching it so that the gooseneck is the same side as the thumbscrews.
There is an Audix clamp similar to this which is cheaper, but I didn't know that at the time!
quality
1
0
Report

Report

google translate fr
Unfortunately there was an error. Please try again later.
j
Je l'utilise sur ma batterie...
joe-tj 21.04.2017
Cette attache micro est conçue pour un tuba, mais elle peux aussi servir à d'autres applications.

Sur les toms de ma batterie, je n'utilise pas de peaux de résonances;
J'ai donc voulu monter mes micros à l'intérieur des fûts, afin qu'ils ne me gênent pas (il m'arrive de taper sur les micros en jouant) et que chaque micro soit mieux isolé du reste de la batterie.

J'ai cherché dans les attaches micros de batterie, mais aucune n'est prévu pour un montage à l'intérieur du fût;
Je me suis donc rabattu sur celle ci.

Verdict :
"C'est juste juste mais ça fonctionne !"

L'écartement maximal de la pince est juste assez large pour la mettre à cheval sur le cerclage du fût (mollettes de serrage à l'intérieur).

J'ai inversé l'orientation du col de cygne (par rapport à ce que l'on voit sur les photos).

Et au niveau de la longueur, le col de cygne est juste ce qu'il faut pour amener mes micros à hauteur des peaux de frappe.

Après un rapide test, le col de cygne à l'air d'être assez "fixe" pour ne pas se déplacer lorsque je joue.

A noter aussi que la partie métallique de la pince (opposé aux mollettes de serrage) est recouverte de feutre, ce qui est primordiale pour éviter les rayures sur votre instrument.

Seul le prix, que je trouve un peux excessif, m'a fait descendre ma note concernant cette attache micro.
Sinon rien à redire.
quality
0
0
Report

Report

google translate fi
Unfortunately there was an error. Please try again later.
VN
Mikkiteline
Ville N. 26.08.2013
Teline ei ole tarpeeksi tukeva kannattelemaan esim. kuvassa olevaa basarimikkiä. Saattaa toimia paikallaan olevan mikkitelineen jatkeena mutta tuubaan kiinnitettynä taipuu ja valuu kelloon.
quality
0
0
Report

Report

google translate de
Unfortunately there was an error. Please try again later.
A
Zufriedenstellend
Analogisch 17.05.2019
Dieser Halter ist ausdrücklich für grosses Blech gedacht, da benutzt man normalerweise keine leichtgewichtigen Kondensatormikrofone. Deshalb hätte ich mir einen etwas stärkeren Schwanenhals gewünscht, damit man auch ein schwereres dynamisches Grossmembran-Mikrofon problemlos nutzen kann. Die Schraube, die den Schwanenhals an der Trichter-Halteklammer fixiert, lockert sich sehr leicht bei nur kleinsten Bewegungen, dann schlingert das Mikrofon hin und her, es folgt halt der Schwerkraft. Thomann hat das Höchstgewicht für nutzbare Mikrofone korrekt angegeben (dankenswert!), ich bin also nicht blind ins Messer gelaufen, deshalb gibt es auch keinen Punktabzug. Ich nutze das Mikro nicht für Liveauftritte sondern nur zur Aufnahme zu Hause, da stört es nicht so, wenn man sich nicht frei bewegen kann. Für meine Ansprüche reicht es - allerdings hätte ich auf jeden Fall einen stärkeren Halter gekauft, wenn es ihn denn für einen vertretbaren Preis (also nicht im gehobenen dreistelligen Bereich) gegeben hätte. Als Tubist hat man es halt in mehr als einer Hinsicht schwer...
quality
0
0
Report

Report